Language
Chinese English español Italiano Giapponese coreano
Home>Main Instruments>Test Charts>SFRPlus Test Charts

SFRplus Chart: Inkjet on Paper - 10:1 & 2:1 Contrast Ratio

SFRplus Chart: Inkjet on Paper - 10:1 & 2:1 Contrast Ratio Instructions Operating Manual SFRplus Chart: Inkjet on Paper - 10:1 & 2:1 Contrast Ratio PDF
This SFRplus Chart: Inkjet on Paper - 10:1 & 2:1 Contrast Ratio Instrument are Certified with
certify
1 Years Warranty (Additional support period of 3 years)

Contrast Ratio Options

  • 10:1 and 2:1 contrast ratios  Use of both contrast levels improves ability to analyze non-linear signal processing, which may not affect the lower contrast 2:1 contrast ratio regions 
  • 10:1 contrast only improves the completeness of 3D maps of performance across the imaging surface.
  • 4:1 contrast ratio matches the upcoming new ISO-12233 specs.  Click here for our 4:1 contrast ratio SFRplus test charts

Paper Type - Semi-gloss or Matte Options

  • Matte paper can be easier to light because it has less specular reflection than the semi-gloss paper.  The MTF is slightly less than semi-gloss paper and does not have as deep dark tones on the stepchart.
  • Semi-gloss paper has slightly higher detail than matte, has deeper black tones on the stepchart, and is recommended for most applications except for wide-angle lenses.

Square Grid Dimension Options

  • 5x9 grid dimension is recommended for for typical DSLR formats with aspect ratios of 3:2 and typical HDTV formats with aspect ratios of 16:9.
  • 5x7 grid dimension  is recommended for typical compact camera formats with aspect ratios of 4:3.

Ink Jet Chart Resolution

This chart, and all our ink jet printed charts have an approximate MTF50 of 5 cycles/mm.  Please keep this in mind when choosing the size of chart.  Using a chart that is too small with a high-resolution sensor can result in the MTF of the chart degrading the measured MTF of the camera system. In addition, it is important to use a chart that is large enough to accomodate the minimum focus distance, as well as the resultion of your sensor. 

Paper Size and Active Area Options

Charts are available in tfive main sizes with variations depending on the grid dimensions selected. It is recommended that the medium sized charts be used to test imaging systems with sensors up to 12 MP, the large charts be used for testing of sensors above 12 MP and up to approximately 24 MP, and the extra-large charts be used for sensor sizes above 24 MP.

Paper Size (Including Margin)

  Square Dimensions
5x9 5x7
X-Small 8.5" × 15" 8.5" × 10"
Small 14" × 24" 14" × 20"
Medium 24" × 40" 24" × 34"
Large 44" × 60" 44" × 60"
X-Large 44" × 74" 44" × 64"

Active Area

The active area of the chart includes white space above and below the top and bottom distortion bars. It is slightly larger than the printed area, which is bounded by the distortion bars on top and bottom. White space is included in active area because test images of the chart must include this white space in order to enable automated processing in SFRplus software.

  Square Dimensions
5x9 5x7
X-Small 7.85" × 15" 6.75" × 10"
Small 12.5" × 24" 13.5" × 20"
Medium 22" × 39.22" 22" × 33"
Large 33" × 59" 40" × 59"
X-Large 42" × 72" 42" × 59"

Color Chart Option

Inclusion of the color chart enables testing of color accuracy. If the color option is selected, the "focus star" pattern that aides in focusing is replaced by a 20 patch color chart.

Pre-Distortion Options

Pre-distorted charts offer the ability to map the outer edges of a wide angle or fisheye lens using SFRplus.  These distortion levels are available

Level Matrix (5x7) Matrix (5x9)
No distortion [0 0] [0 0]
Distort [0.833 1.123] [0.833 1.375]
Distort+ [1.167 1.577] [1.167 1.982]
Ultradistort [1.333  2.313] [1.333 2.958]

Our Valued Clients

  • our customer Truly Opto Electronics
  • our customer oppo
  • huawei
  • our customer o film
  • our customer TRANSSION
  • our customer SEMCO
  • our customer q tech smart vision
  • our customer Largan Precision

FAQs About  SFRPlus Test Charts

 The five common gloss levels are:

1. Flat/Matte (0–10 GU)

2. Eggshell (10–25 GU)

3. Satin (26–40 GU)

4. Semi-gloss (41–70 GU)

High Gloss (71–100+ GU)
These levels vary slightly depending on industry and standards used.


Haze measurement can be distorted by scratches on the surface, dust, temperature, and light. 

The gloss meter is used to measure the gloss level: it is a device that directs the light at a fixed angle and reads the intensity of the reflected light. The angles, such as 60°, 20°, or 85°, are applied depending on the type of surface and the range of gloss.


 Inquiry - quotation - communication - order confirming - deposit payment - production - testing and debugging - balance payment - packing - delivery - customer receiving - after service. 

When detecting color differences, the first factors to consider when selecting a light source include its stability, directionality, lifespan, and the effectiveness of the ultimately obtained spectral curve. The illuminant of a colorimeter is a fixed bulb, such as a tungsten lamp，LED light or a long-life xenon lamp. However, for the same color sample, the results displayed by the instrument vary under different light sources. This is because different light sources cause different absorption and reflection of light on the sample, leading to differences in how both the human eye and the instrument perceive the color. 

In general, the D65 light source is used in the application of coil steel inks for construction. The D65 light source is equivalent to average daylight. Most coil steel inks for construction are used outdoors, and sunlight is regarded as the standard light source in outdoor environments. For household appliance coil steel inks, due to their usage characteristics, they are mostly used indoors. Therefore, the A standard light source is adopted for color measurement of samples based on indoor lighting conditions. The A light source is a carefully specified tungsten light source. Other light sources, such as fluorescent light sources, can be used in many types of applications. For example, some textile factories use fluorescent light sources. Therefore, a reasonable light source should be selected as the mutually recognized measurement method based on actual usage conditions and user requirements. Once agreed upon by both parties, color measurement must be conducted under the same conditions. This helps reduce unnecessary systematic errors and human errors, achieving the optimal consistency in color measurement. 

The 3nh high-precision spectrophotometric colorimeter adopts a combined LED light source with long lifespan and low power consumption, which includes UV (ultraviolet) and UV-excluded options. This design can meet the color difference detection needs of different users and supports the selection of multiple light source modes.

a. When the colorimeter is disconnected to the PC, "Connection Timeout" will occur. At the moment, you have to check whether the USB cable is well connected the colorimeter and the PC. Then you can re-plug the USB to try out.

b. After ensuring the colorimeter is connected to the PC with USB cable, turn on the colorimeter and enter the main menu. Select "Comm" and press "Enter" key to start communication.

c. Turn off CQCS3 software, and reopen it.

Related SFRPlus Test Charts You May Also Like

Copyright ©1998 - 2026 Guangdong Threenh Technology Co.,Ltd. Privacy Policy

Give us a call!

Discuss your project with one of our product specialists:

0086 755 26508999

Need pricing?

We respond to quote requests within 1 business day.

service@3nh.com

Already know what you need?

Submit a demo request for the product you're interested in.

Get a Demo
Leave Your Message
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it. Privacy policy